How to Configure PRI in SV8100

Installation and configuration of IDSN PRI in NEC SV8100 is simple and plug and play. If the slot is not configured, then switch off the system install the card and switch on. SV8100 will sense the card and configures itself. The following commands are minimum required to

Activate PRI card.

10-51-01 = 0, select card as PRI

10-03-01 = 1, Assign PRI card as T bus / Trunk

10-03-02= (1-200) you can only read this information which is the starting trunk number

10-03-03 = 1 / 0, CRC4 on / off

10-03-18 = 2, Set this as National number for assigning type of number. Check with your PRI service provider

10-03-19 = 1, Assign as ISDN numbering plan

Once the card is up, it can be configured to work DID, VRS etc..

How to Configure PMS in NEC 2000 IPS

Property Management System Integration with AP00 on RS-232C:

The Application Processor card (AP) manages guest and administration extension status and stores call information. The AP card provides four RS-232C interface ports for a Property Management System (PMS) terminal, a Station Message Detail Recording (SMDR) / MCI, MCI terminal and a Hotel Printer.

Property Management System (PMS):

PBX provides a data link interface to the customer supplied Property Management System (PMS) accommodating hotel management features. The PMS can be any computer connected to the PBX via a RS-232C or a LAN interface. It communicates with the PBX using the specified protocols.

The data link interface allows the PMS to accommodate both front- and back-office hotel management features, by providing a means of communication between the PMS and the PBX for features such as 

Check In/Check Out

Message Waiting

Station Message Detail data

Do Not Disturb

Room cutoff.

Commands:

Assign AP00 card as AP00

050 > AP no (04 to 15) > 04: AP00

Note: AP no is the sense switch settings position

AP00 initialization

Note: Make the AP00 card to off-line mode by changing the switch SW1 (2,3) to off position.

D101 > 0000 > CCC

Assign buffer limit in AP00

D003 > 29 > 1000

Clear billing buffer

D102 > 0000 > CCC

Note: Revert the switch 2, 3 to on

Initialize all the four ports data

D100 > D001 > CCC

PMS configuration in port 0:

D001 > 20 > 2 = 1200 bps baud rate

D001 > 21 > 0 = Stop bit length 1

D001 > 22 > 0 = Data length 8

D001 > 23 > 1 = Parity Even

D001 > 80 > 4 = PMS

D001 > 81 > 0

D001 > 82 > 6 = PMS Format

D001 > 83 > 0

D001 > 84 > 6 = IMS Procédure

D001 > 85 > 49

D001 > 86 > 33

D001 > 87 > 8

D001 > 89 > 70

D001 > 90 > 70

D001 > 91 > 3

D001 > 92 > 15

D001 > 93 > 3

D001 > 94 > 32

D001 > 95 > 24

D001 > 96 > 24

D001 > 98 > 0

Once this is done PMS is ready to test. PMS can be tested using PMS simulator not in hyper terminal. Remaining ports can be assigned for SMDR only, MCI for voice mail integration or SMDR and MCI together.

How to Access SN716 Setup Menu

Configuration Menu is used to assign the following data’s for the SN716 DESKCON / ATTENDANT CONSOLE.

1. HEADSET/HANDSET

2. HEADSET TYPE

3. MUTE

4. REC CONTROL

5. PAGE CONTROL

6. SUP CONNECTION

7. REC VOLUME

8. BLF

9. HOLD/START/RELEASE/SWAP

10. 2ND RINGING

11. RINGING

12. RECEIVER VOL SET

13. FUNCTION KEY SWAP

14. RINGER VOLUME IN PB

15. POWER CONTROL

16. CONF. TONE FOR ALL KEYS

NOTE: All of the above data’s are not available in all the system; it depends on model and version.

To login in to Configuration Menu

1. Power off the SN716 console

2. Press L4, L5 and SRC key simultaneously and turn on the power (Plug the AC/DC adapter of the SN716 DESKCON in AC outlet) and follow the display and proceed accordingly.

SN 716 attendant console can be locked and unlocked for security reasons, to avoid misuse through a feature called Attendant console lockout release.

NEC SN716 Deskconsole Lockout Release

FEATURE DESCRIPTION

This feature allows the operators to lock and unlock the attendant console with password. This feature disables the consoles from originating or receiving calls and setting or resetting service features. A password is required to return the console to its normal operating condition.

To Lock Console 

1. Press an idle LOOP key and associated green LED lights (depending on software version).

2. Dial feature access code or press MODE key and the associated red LED lights. The LCD displays “ACTIVE” as normal mode and the green LED of ACTIVE key lights.

3. Press the soft key corresponding to LKOUT and the associated red LED lights. The LCD display changes from “ACTIVE” to “LKOUT”.

4. Press the ANSWER key, LCD displays “SET LKOUT”. The mode of the console is changed from normal to lockout condition.

5. Press the RELEASE key.

To un lock console 

1. Press MODE key and the associated red LED lights.

2. Dial password.

3. Press the ACTIVE key and the associated green LED lights. The LCD display changes from “LKOUT” to “ACTIVE”.

4. Press the ANSWER key and receive Service Set Tone. The LCD displays “SET ACTIVE”. The mode of the console is now changed from lockout to normal condition.

5. Press the RELEASE key.

HOW TO ASSIGN PASSWORD IN NEC SN716 CONSOLE FOR 2000 IPS AND SV 8300

This program is used to assign password to unlock the SN716 attendant console.

1. 6030 > 0 > XXXXXXXX (pass code) maximum 8 digits, if the data is not set the default value is 12345678.

Toll Restriction Override in NEC SV8100

Toll restriction override allows an extension user to temporarily bypass an extension’s toll restriction class. This helps a user to place a toll call by dialing a PIN which is normally prevented. This also prevents making un-authorized toll calls by others. This configuration is common for AspilaTopaz, AspilaEx and SV8100.

Toll Restriction Override

1. Set up toll restriction class for all extensions and block toll calls to required extensions.

2. Go to 11-11-36: Set up walking toll restrict dial access code. Default = 763 if required change it.

3. 20-08-06: Make sure that Toll restrict override is set to ON, per class of service.

4. 21-01-07: Toll restriction override timer. Default 10 seconds. This is the time the system waits for you to dial after entering the override code before restrict is applied again.

5. 21-14-01: Enter walking PIN. 6 Digits in length (Max 500 entries)

6. 21.14.02: Enter toll class for this PIN (toll restriction applied after dialing pin)

7. Make sure 35‐02‐07 is turned on to output the PIN ID in the SMDR.

8. To test. Dial access code (default 763) + PIN+ get internal dial tone + dial 9 / 0 plus the outside number.